Abstract :

 A pump driving motor is an electric motor utilized to operate water pumps. At PERUMDA Tirta Taman, Bontang City, six motors and three pumps are employed, where the submersible pump motor functions to extract raw water from wells, the feed pump transfers water to the clarifier tank, the dosing pump supplies chemical reagents, the backwash pump and root blower are used for cleaning the filtration tank, and the distribution pump delivers treated water to consumers.

Field measurements show that the main protection for the submersible pump motor is a 160 A MCCB, whereas the calculated rating is 290 A. The main protection for the feed pump and backwash pump (1 and 2) in the field uses a 100 A MCCB, while calculations show 73.5 A and 72.5 A. The dosing pump motor uses a 6 A MCB in the field, with a calculated value of 3.6 A. The root blower motor utilizes a 20 A MCB in the field, while its calculated rating is 30.75 A. The distribution pumps (1 and 2) use a 125 A MCCB, whereas the calculated protection rating is 202.5 A.

For the conductor sizing, a 4 × 35 mm² NYY cable is installed for the submersible motor, while its calculated ampacity is 145 A. The dosing motor uses a 3 × 2.5 mm² NYY cable with a calculated capacity of 1.8 A. The feed pump and backwash pump use a 4 × 6 mm² NYY cable, with calculated ampacities of 36.75 A and 36.25 A, respectively. The root blower uses a 4 × 2.5 mm² NYY cable with a calculated rating of 15.37 A, and the distribution pump (1 and 2) uses a 4 × 25 mm² NYY cable with a calculated rating of 101.25 A.

---

Keywords :

Backwash Pump, Distribution Pump, Dosing Pump, Feed Pump, Induction Motor, Pump Driving Motor, Submersible Pump, Water Treatment Process.

---

References :

1. G. D. Arjana, “Picobox at PDAM Denpasar City,” Scientific Journal, vol. 7, no. 3, pp. 15–24, 2020.
2. I. Muzani, “Testing Analysis of Deep Well Submersible 3-Phase Induction Motor Connected in Star-Delta with TDR System Circuit at PDAM Tirta Baribis Brebes,” Semarang University (USM), pp. 1–10, 2022.
3. C. Panigas, A. Budiono, and D. Setyanta, “Determination of Dosing Pump Opening Flow Rate for Disinfection Process of Deep Well at Tandon Betek,” Distilat: Journal of Separation Technology, vol. 9, no. 4, pp. 338–344, 2023..
4. Mirelda Sari and R. Rinawati, “Analysis of the Effect of Backwash on Clean Water Treatment at Water Treatment Plant (WTP) 1 PDAM Way Rilau Bandar Lampung,” Analit: Analytical and Environmental Chemistry, vol. 6, no. 2, pp. 198–208, 2021.
5. P. Adji and A. Amalia, “Modeling of Clean Water Distribution Network at CV. X for Industrial Areas Using EPANET Application,” Indonesian Journal of Applied Science and Technology, vol. 3, no. 2, pp. 67–75, 2023.
6. R. Pattiapon and J. J. Rikumahu, “Design and Construction of Three-Phase Induction Motor Teaching Aid,” ELKO Journal (Electrical and Computer), vol. 1, no. 1, pp. 35–43, 2021.
7. Simangunsong, U. Darma, and A. Medan, “Study of 3-Phase Induction Motor Star System Using Star-Delta Method at PT. Toba Pulp Lestari Tbk,” n.d.
8. Fartino, T. Tarmizi, and M. Syukri, “Design Study of Automatic Power Factor Correction Device,” Journal of Computer, Information Technology, and Electrical, vol. 5, no. 1, pp. 11–18, 2020.
9. Yendi and L. Sigit, “Analysis of Electrical System Power Factor Improvement,” Journal of Science & Technology Faculty of Engineering, vol. 11, no. 1, pp. 103–113, 2021.
10. Tohir, “Design and Construction of 3-Phase Induction Motor Control Based on PLC Using Function Block Diagram Programming Method,” in Proceedings of National Seminar on Electrical Engineering UIN Sunan Gunung Djati, Bandung, Indonesia, Nov. 2019, pp. 501–511.
11. D. Azum and I. Harjanta, “DOL (Direct Online) Circuit at PT. Urip Gumulya,” SENS, vol. 7, pp. 1–8, 2022.
12. P. Adji and A. Amalia, “Modeling of Clean Water Distribution Network at CV. X for Industrial Areas Using EPANET Application,” Indonesian Journal of Applied Science and Technology, vol. 3, no. 2, pp. 67–75, 2023.
13. M. Asyadi and Muliadi, “Analysis of Pump Working System at PDAM Tirta Daroy Banda Aceh,” Aceh Journal of Electrical Engineering and Technology, vol. 1, no. 1, pp. 1–5, 2021.
14. T. Hidayat, “The Effect of Pump and Impeller Modification on Shimizu PS-128 BIT Pump Performance,” in Proceedings of The 13th Industrial Research and National Seminar, pp. 740–747, 2022.
15. “Definition of Pump.” Amni.ac.id. http://amni.ac.id/1751/2/BAB%202.pdf (accessed Jan. 1, 2023).
16. G. D. Arjana, “Picobox at PDAM Denpasar City,” vol. 7, no. 3, pp. 15–24, 2020.
17. E. A. Lestari and P. Oetomo, “Analysis of the Most Efficient Electrical Power Conductor Selection in High-Rise Buildings,” Sinusoida, vol. 23, no. 2, pp. 61–68, 2021.
18. Sugianto, A. S. Fahrezi, and P. Oetomo, “Planning of Electrical Installation in Hospital Buildings,” Sinusoida, vol. 24, no. 2, pp. 18–25, 2022.
19. General Requirements for Electrical Installations (PUIL) 2020 – Part 1: Introduction, Fundamental Principles and Definitions, SNI 0225-1:2020, National Standardization Agency (BSN), 2020.
20. Bunga, M. Pakiding, and S. Silimang, “Design of Remote Load Control System Using Smart Relay,” Journal of Electrical and Computer Engineering Sam Ratulangi University Manado, vol. 4, no. 5, pp. 65–75, 2019.
21. Panjaitan, “Design and Construction of Automatic Genset Using Contactors with 12 V, 50 Ah Battery Power,” Design and Manufacture of Automatic Pest Sprayer on Rice Plants with SMS Gateway Information Based on Arduino, pp. 1–12, 2019.
22. Putra Harahap, W. Dwiono, and N. Harpawi, “SMS-Based Power Source Switching Hardware Circuit,” Journal of Industrial Electronics, vol. 5, pp. 40–49, 2019.